Allied Data Technologies 811 Manual de Instalação

Installation Manual CopperJet 16xx series Based on firmware 6.10 June 2006

Chapter 3: Connecting the CopperJet CopperJet 1620 CopperJet 1622 PWR USBADSL1234EthernetPower supplyDSL ProviderRJ-11RJ-45StraightComputerPowe

Chapter 4: Before you start 4 Before you start The following information may be required for configuring the CopperJet. If you do not know if all t

Chapter 4: Before you start 4.6 VoIP settings The following VoIP settings should be available during configuration. • Signal protocol (SIP or MGCP)

Chapter 5: Configuring the CopperJet 5 Configuring the CopperJet Configuration of the CopperJet ADSL router can be done through the build-in HTTP We

Chapter 5: Configuring the CopperJet 5.2 Quickstart With the Quickstart option you can configure your CopperJet in only a few steps. The number of ste

Chapter 5: Configuring the CopperJet 5.3 System The System menu contains options which provide information about the CopperJet and enable you to manag

Chapter 5: Configuring the CopperJet • when the event occurred (in seconds since your system was restarted) Note: If you are using the SNTP module, th

Chapter 5: Configuring the CopperJet it will also have an idle timeout of 10 minutes, whether the session is TCP, UDP or fake (i.e., anything else). U

Chapter 5: Configuring the CopperJet 5.3.6 Backup Configuration Profile The Backup page allows you to backup your configuration profile to your compu

Chapter 5: Configuring the CopperJet 5.4 Configuration The Configuration menu enables you to configure the basic and advanced network settings of the

Document History Date Version Status Description 02 June 2006 1.0 Final Updated to firmware 6.10

Chapter 5: Configuring the CopperJet Fill in the required fields. Username: Username of the new user. Password: Password of the new user May

Chapter 5: Configuring the CopperJet 5.5 LAN Connections LAN Connections allows you to configure the Ethernet connection. The Ethernet connection CANN

Chapter 5: Configuring the CopperJet This page contains the Default LAN Port table that allows you to configure the following: IP Address: Configure

Chapter 5: Configuring the CopperJet 5.6 WAN Connections To create a DSL Connection, you need to add a WAN connection. Depending on the network of you

Chapter 5: Configuring the CopperJet 5.6.1 Configuring RFC1483 Bridged service attached to the Bridge One of the most commonly used connections is RF

Chapter 5: Configuring the CopperJet 5.6.1.1 Configuring DHCP on your network card To configure DHCP on a network card for a Windows PC, follow the s

Chapter 5: Configuring the CopperJet 5.6.2 Configuring RFC1483 Routed service attached to the Router A RFC 1483 Routed connection is used when your S

Chapter 5: Configuring the CopperJet 5.6.3 Configuring RFC1483 Bridged service attached to the Router RFC1483 Bridged service attached to the Router

Chapter 5: Configuring the CopperJet 5.6.4 Configuring IPoA routed service attached to the Router An IPoA routed connection is used when your Service

Chapter 5: Configuring the CopperJet 5.6.5 Configuring PPPoA routed service attached to the Router PPPoA routed is mostly used when your Service Prov

Product DISCLAIMER This manual by ALLIED DATA TECHNOLOGIES B.V. (hereafter referred to as ALLIED DATA TECHNOLOGIES) is a reflection of the current st

Chapter 5: Configuring the CopperJet Password: Fill in the password provided by your service provider. Password (confirm): Fill in the password pr

Chapter 5: Configuring the CopperJet 5.6.6 Configuring PPPoE routed service attached to the Router PPPoE routed is mostly used when your Service Prov

Chapter 5: Configuring the CopperJet Authentication: Choose the authentication method provided by your service provider. None: You don’t need to s

Chapter 5: Configuring the CopperJet 5.7 Security The CopperJet has extensive Security functionality like a Stateful Inspection Firewall, Network Addr

Chapter 5: Configuring the CopperJet 5.7.2 Configuring Security Interfaces Before Security options can be configured, there must be at least 2 Securi

Chapter 5: Configuring the CopperJet 5.7.3 Configuring Network Address Translation (NAT) The Network Address Translator (NAT) implements Port Address

Chapter 5: Configuring the CopperJet 5.7.3.1 Configuring NAT global addresses Global address pools allow you to create a pool of outside network addr

Chapter 5: Configuring the CopperJet To set up a reserved mapping on your existing NAT enabled interfaces, go to the Configuration menu and select Sec

Chapter 5: Configuring the CopperJet Important: Make sure the Internal IP address is in the same subnet as your CopperJet LAN IP address. To delete

Chapter 5: Configuring the CopperJet For a TCP portfilter click on Add TCP Filter. The Firewall Add TCP Port Filter page is displayed: omplete the s

Contents 1 Packaging contents ...4 2 LED Indicators and bac

Chapter 5: Configuring the CopperJet 5.7.8 Configuring validators A validator allows/blocks traffic based on the source/destination IP address and net

Chapter 5: Configuring the CopperJet 5.7.8.1 Configuring Triggers A trigger allows an application to open a secondary port in order to transport packe

Chapter 5: Configuring the CopperJet secondary session to be initiated only to/from the same remote host. Default allow. Max Activity Interval: Type

Chapter 5: Configuring the CopperJet 5.8 Search Service The Search Service menu allows you to set auto-provisioning to scan a fixed list of PVCs for p

Chapter 5: Configuring the CopperJet 5.9 Zero Installation PPP Bridge (ZIPB) Dynamic ZIPB, also known as PPP Half Bridge, allows a home user to share

Chapter 5: Configuring the CopperJet Click on the Enable button to enable ZIPB. Click on the Choose which computer will use the public IP address dr

Chapter 5: Configuring the CopperJet 5.9.4 ZIPB Advanced configuration Note: You must ensure that ZIPB is in a disabled state before you carry out an

Chapter 5: Configuring the CopperJet 5.9.5 Limitations of ZIPB If Dynamic ZIPB is enabled, traffic originating from your CopperJet, such as pings or o

Chapter 5: Configuring the CopperJet 5.10 IP Routes This option allows you to create static IP routes to destination addresses via an IP interface nam

Chapter 5: Configuring the CopperJet 5.11 DHCP Server DHCP allows you to dynamically assign IP address to the computers connected to the Ethernet of t

5.10.1 Creating an IP V4 Route ... 46 5.11 DHCP Server ...

Chapter 5: Configuring the CopperJet This pag • Set the subnet for the D the same subnet used on the IP interface by selecting Ethernet-0. client t

Chapter 5: Configuring the CopperJet Click on the Option name drop-down list and select a name. Type a value that matches the lected option name in t

Chapter 5: Configuring the CopperJet 5.11.3 Disabling DHCP Server To disable the DHCP Server, go to the Configuration menu and select DHCP server. The

Chapter 5: Configuring the CopperJet 5.12 Configuring DHCP Relay DHCP Relay provides a means for relaying DHCP and BOOTP requests from a subnet to wh

Chapter 5: Configuring the CopperJet 1. Click on the New IP interface drop-down list and select an interface. 2. Click Add. 5.12.3 Adding a DHCP serv

Chapter 5: Configuring the CopperJet The DNS servers can be discovered automatically through DHCP on the WAN interface OR configured manually. 5.14.1

Chapter 5: Configuring the CopperJet When you are finished with configuring DNS Relay for the WAN connection, click on Apply. Go to the Configuration

Chapter 5: Configuring the CopperJet 5.14.3 Configuring DNS relay LAN database The LAN database lists details about local host names and IP addresses

Chapter 5: Configuring the CopperJet 5.15 Configuring Dynamic DNS Client (DynDNS Client) If some host has a dynamic IP address that keeps changing fr

Chapter 5: Configuring the CopperJet parameter accepts these values: dyndns, dyndnscustom, dyndns-static, and tzo. User Name: Username registered at

Chapter 1: Packaging contents 1 Packaging contents The packaging should contain the following parts: ++++Ethernet RJ45Straight or CrosscableRJ11

Chapter 5: Configuring the CopperJet 5.16 Configuring Simple Network Time Protocol (SNTP) Client Configuring your device as an SNTP client allows you

Chapter 5: Configuring the CopperJet 3 If you enabled unicast mode in the previous step, you can set the dedicated unicast server by either IP address

Chapter 5: Configuring the CopperJet 5.17 Configuring Voice over DSL Basic configuration of the Voice over DSL (VoDSL) settings in the CopperJet Inte

Chapter 5: Configuring the CopperJet CAS: Channel Associated Signaling (CAS) is used in bit-based schemes where dedicated signaling bandwidth is r

Chapter 5: Configuring the CopperJet flashmax 200 [enter] 5.17.2.2 Initial ring timing for CLIP Because the requirements of the initial ring timing d

Chapter 5: Configuring the CopperJet Example: to set the ring cadences enter the following commands: cadence 0,2000,4000,0,0,0,0 [enter] cadence 1,8

Chapter 5: Configuring the CopperJet 5.18 Configuring VoIP VoIP enables telephone calls to be made over an IP network. This enables DSL Service provid

Chapter 5: Configuring the CopperJet 5.18.1 Configuring VoIP using SIP SIP stands for Session Initiation Protocol (SIP), an application-layer control

Chapter 5: Configuring the CopperJet • IP Domain name - The domain name should be a FQDM (Fully Qualified Domain name). SIP Silence Suppression: Thi

Chapter 5: Configuring the CopperJet IP Precedence: IP Precedence Bits: Default “0-Routine”. An independent measure of the importance of this data

Chapter 2: LED Indicators and back panel 2 LED Indicators and back panel Before you begin with the installation, please take a moment to become mor

Chapter 5: Configuring the CopperJet - 1-Low - 2-Medium - 3-High In the DSCP bits field, you will see the binary value of what you have selected.

Chapter 5: Configuring the CopperJet • x.T - any number of digits followed by a timeout to dial the digits. This is not a special call code. • ##S -

Chapter 5: Configuring the CopperJet -->voip set sip proxyroute strict <Enter> 5.18.1.8 Configuring Registration Expires This command spe

Chapter 5: Configuring the CopperJet -->voip set sip outboundservertransport udp <Enter> 5.18.1.13 Enable SIP tracing in the CopperJet T

Chapter 5: Configuring the CopperJet 5.18.2 Configuring VoIP using MGCP MGCP stands for Media Gateway Control Protocol. It consists of a Call Agent, w

Chapter 5: Configuring the CopperJet • G.726 (32kb) and • G.729 a/b After the correct settings are filled in, click on Apply. Go to the Configurati

Chapter 5: Configuring the CopperJet 5.18.2.3 Configuring MGCP Domain -->voip set mgcp domain <domain> <Enter> This command is used

Chapter 5: Configuring the CopperJet 5.19 DSL Line The DSL Port menu allows you to configure specific DSL settings. Usually, the default settings are

Chapter 5: Configuring the CopperJet Reset Defaults: False at default. After you changed the configuration, click on Apply. Don’t forget to save

Chapter 6: WAN Configuration Examples Page 77 6 WAN Configuration Examples In this chapter is described how to configure a basic/standard WAN conne

Chapter 2: LED Indicators and back panel 2.2 CopperJet 16xx series back panel CopperJet 1610 CopperJet 1612 Power ADSLUSB EthernetBack panelPo

Chapter 6: WAN Configuration Examples Page 78 6.3 Configuring a PPPoA connection with NAT In this section is described how to configure a PPPoA conn

Chapter 7: Glossary Page 79 7 Glossary 10BASE-T A designation for the type of wiring used by Ethernet networks with a data rate of 10 Mbps. Also kn

Chapter 7: Glossary Page 80 DHCP Dynamic Host Configuration Protocol DHCP automates address assignment and management. When a computer connects to t

Chapter 7: Glossary Page 81 Hub A hub is a place of convergence where data arrives from one or more directions and is forwarded out in one or more d

Chapter 7: Glossary Page 82 network A group of computers that are connected together, allowing them to communicate with each other and share resourc

Chapter 7: Glossary Page 83 RJ-11 Registered Jack Standard-11 The standard plug used to connect telephones, fax machines, modems, etc. to a telephon

Chapter 7: Glossary Page 84 twisted pair The ordinary copper telephone wiring used by telephone companies. It contains one or more wire pairs twiste

Chapter 3: Connecting the CopperJet 3 Connecting the CopperJet To connect the CopperJet to the computer, you must have installed an Ethernet 10/100